Programmable Watch Winder

Remove the cuff from the winder drum by pulling firmly on the two tabs. Close the  trap or bracelet of your watch. Compress the cuff and slide your watch over the cuff, watch dial facing outwards. Push the cuff into the drum until it locks into place, an audible click will be heard.

Note: Never insert or remove your watch when the drum is rotating.

With the adapter connected, turn the right hand knob to the "ON" position. The display will be lit and you will have 10 seconds to initiate your personal settings. When after 10 seconds there has been no change to  settings, the program starts the winder. 

Turn the knob on the left to the required direction setting.  A= clockwise , B= counter-clockwise or C= bi-directional. The selected setting will be displayed on the LCD display.

Controls: The Module 2.7 has two buttons marked "+" and "-" and two selection knobs. When the right hand side knob is turned to OFF, the unit will be deactivated and the display will be switched off. If either of the two power sources is maintained, the pre-set parameters such as the turns per day (TPD) or the delay start time (DST) of the unit will be memorized. However, the unit will not respond to the buttons and selection knobs when in the "OFF" mode.

Rotations: By pressing the"+" or"-" black buttons you can increase or decrease how many turns per day you want your watch to rotate. Changes are made "UP" or "DOWN" in increments of 50 rotations. Minimum setting is 300 and maximum setting is 1200 Turns Per Day. The LCD display will show the current setting. The default setting is 900 TPD.

Delayed Start: If you would like to manually delay the start time turn the right knob to 0 and press the "+"or"-" buttons to select 6, 12, 18, 24, 30, 36, 42, 48, 54, 60, 66 or maximum 72 hours. After 10 seconds the setting is stored and delay countdown will begin based on the selected
setting. Delay countdown starts showing hours remaining to start, followed by minutes and finally seconds. The display will continuously switch between showing the delay countdown and rotation setting.

This Module 2.7 winder comes with a power adapter, model number (TY0500100), (AC/DC 5.0-volt output) and will also run on "D" cell batteries (with the exception of the 4, 6, and 8 piece winders). The winder will automatically switch to mains power if both power sources are connected.

Your watch your rules. You can set your watch to start in any position and it will return home to the same position when the cycle is complete.

The first time you turn your winder on you will notice that the drum rotated and then rests. The drum will always stop at this position, during and at the end of all cycles.

That means that if you place your watch inside the drum so the position is 12 o'clock, the watch is at the top, and then during all test cycles, your watch will come to a rest at the 12 o'clock position. You can choose any position you like.

The LCD backlight assists users to read the LCD. It will be activated when either the control knobs or buttons have been manipulated. In order to save power, the backlight will automatically turn off when there is no input detected for about 20 seconds.

There are two status LEDs, one green and one red. The green LED indicates normal operation. When the "Power" knob is not in the "OFF" position, the green LED will be flashing. The red LED will be activated when the unit detects that the drum is not rotating properly. After a short pause the winder will start again to see if the drum rotates properly. If not, the red LED will start flashing again. This process will continue until the drum starts rotating properly.

The module 2.7 provides 19 TPD settings and 3 directional modes, giving 57 possible rotation programs. There are 19 distinct rotation programs with respect to the TPD settings and their parameters are listed in the following table. The actual number of rotations will be double that of the TPD value when the rotator is in bi-directional mode.

Note: There is no magic number of rotations that will wind your watch. Things such as how active you are, how many complications your watch has, how frequently you use the chronograph function, how frequently you wear your watch, the watch make, how long it has been since it was last serviced and a host of other variables will impact what your watch requires to stay wound. You will have to make this determination by trying the various settings.

This cable is a convenient and effective way of connecting multiple watch winders together, allowing them to run off only one power source. This reduces the need for clunky power strips and A/C adapters. Perfect for use with all WOLF winder systems.